Serge Full Panels

In 2014, three Serge front panels in 4U format - Edelweiss, La Bestia and Sturm & Drang - were offered in a panel run and quickly sold out. In 2016, if there is enough interest, Random*Source will offer updated versions as Edelweiss II and La Bestia II as well as the corresponding Random*Source pcb sets (under license from by Serge Tcherepnin).

How it works: The La Bestia II front panel can now be (pre-)ordered by placing a non-refundable deposit of € 30 towards the panel price of € 95. The run requires a minimum size (number of pre-orders). If the panel run does not happen for whatever reason, you will simply get your deposit back through paypal. However, if the run happens, but you simply change your mind, your deposit cannot be refunded. Pcbs will be offered on this page as they are / become available.

There should be so shipping cost if you only order the La Bestia deposit. Please reload this page while pressing SHIFT in case shipping cost gets added.

The smallprint: sourcing and (smt) pcb production is a huge challenge, especially since the pcbs are also sold as 4x4 modules, so there is no guarantee that all the pcbs will be available at the same time or that stock levels will be sufficient. It is recommended to order pcbs when they are available, i.e. don't wait for others to become available (again) to optimize shipping or similar. Also, this is DIY and while many boards are not particular difficult, it is not recommended to start with a full panel as a beginner's project or without sufficient soldering experience.

The panels on this page are all in the classic Serge dimension ("4U" panel height) and the typical banana jacks. pcbs are designed to be powered by +/-12V.

Looking for Serge in Euro (3U)?. Check out our Serge for Euro page.

 

La Bestia II

Serge La Bestia V2

La Bestia II is a very dense voice and timbre panel, featuring the new 2017 Serge NTO with its amazing waveshaper. A DSG mk2 in an oscillator ("Timegen") configuration offers up to 4 octaves of tracking. The famous Serge Wave Multipliers, an SSG and a Serge Noise Source, the 2 most prominent Serge filters, a high-end audio mixer and the R*S Stereo Mixer make this a powerful soundshaping tool and ideal companion for Edelweiss II.

- UPDATE: PANELS ARE HERE -
Shipping options are still to be validated, shipping cost calculation is not updated yet and possibly erroneous, so please consider shipping cost as preliminary.

La Bestia II build doc
La Bestia II front panel - faceplate only! - (17")€ 100
La Bestia II remainder* - requires previous deposit! - (17")€ 70
La Bestia II panel + regular boat + psd pcb (17")€ 250
La Bestia II + XL boat + psd pcb (17")€ 310

La Bestia II - Modules

Please note that all prices exclude shipping and the shipping cost calculated by the shop software may be incorrect, especially if the order contains boats as the actual shipping depends on destination / size / weight!

La Bestia II is specifically designed to host the R*S modules listed below - please do not (pre)order a panel if you do not plan to build it with these modules.

Serge NTO Build docSMT(3")€ 260
Audio Mixer (MUSES edition) Build docSMT(1")€ 70
Serge Wave Multipliers (VCM) SMT(2")€ 150
Serge SSG + Noise Source Build docSMT(2")€ 130
Serge DSG mk2 Build docSMT(2")€ 180
Serge Variable Slope VCF (VCFS) Build docTH(2")€ 60
Serge Variable Q VCF (VCFQ) Special* Build docSMT-version(2")€ 120
Serge Variable Q VCF (VCFQ) classic* Build docTH(2")€ 60
Stereo Mixer Build docSMT(2")€ 160
 total(16")€ 1070 or 1130
* The VCFQ SMT-version is an alternative to the classic (through-hole) version - pick either one.
Please note that neither version contains the THAT2180 ICs (or any other through-hole parts).

 

Edelweiss II

Serge Edelweiss V2

Edelweiss II may look like an ideal control panel, but it is also quite powerful in the audio range. Many R*S modules like the DSG mk2 and SSG have been optimized for audio performance and can be used as oscillators, filters or lowpass gates.
Please note that all prices are excluding shipping and the shipping cost calculated by the shop software may be incorrect, especially if the order contains boats as the actual shipping depends on destination / size / weight!

Edelweiss II front panel

Edelweiss II front panel, 17" wide, 4U, 2mm anodized aluminum. Price is € 100. Panels have arrived! :-) If you pre-ordered (by ordering a deposit), please pay the remainder by ordering below. To place a fresh order, you can either order the Edelweiss II panel with a regular R*S boat (and a PSD pcb) or with a R*S XL boat (and a PSD pcb).

Edelweiss is specifically designed to host the R*S modules listed below - please do not (pre)order a panel if you do not plan to build it with these modules.

Edelweiss II front panel - faceplate only! - (17")€ 100
Edelweiss II remainder* - requires previous deposit! - (17")€ 70
Edelweiss II panel + regular boat + psd pcb (17")€ 250
Edelweiss II + XL boat + psd pcb (17")€ 310

Edelweiss II - Modules

Serge DSG mk2 modern Build docSMT(3")€ 180
Serge Dual CV-Processor SMT(2")€ 30
Serge DSG mk2 classic Build docSMT(3")€ 180
Pulse Divider and Boolean Logic Build docTH(3")€ 55
Serge N Comparator (NCOM) SMT(1")€ 75
Serge Random Source Build docSMT(2")€ 130
Serge SSG Build docSMT(2")€ 120
 total(16")€ 770

Boat / PSD

Regular and XL boats (to house Edelweiss + 2 4x4 modules) are available here.


Random*Source auf Facebook